RR Series packaged air conditioning units air cooled type, suitable for installations in room, shelter for radio base station and data processing centre.

RR air conditioning units can be supplied in two different versions:

· INDOOR installation
· OUTDOOR installation

The air conditioner without the Free-cooling module is CONVENTIONAL type: the cooling air is taken from the UPPER side and sent fromto DOWN side of the air conditioner.
The air conditioners are equipped with internal controller and temperature and pressure probes allowing the implementation of an autonomous conditioning systems and assuring a complete redundance of all the control and conditioning functions.

The electronics is provided with real time clock. The unit is equipped with remote PLC display for visualization of parameters, states and alarms.

In addition the unit can be equipped with serial RS232/485, Ethernet of GSM/GPRS card in order to allow communication with external equipment.

Packaged air-to-air air conditioning units, designed and manufactured to work in industrial environments, in presence of dust and vibrations and exposed to high temperature.

ACUS-F Series conditioners have been designed to cool crane control cabins: every component has been designed, selected and placed to satisfy all the needs of control cabins, to simplify the access to the internal parts and to minimize the maintenance.

The units must be installed on the floor, on horizontal surfaces and are equipped with air flows channeling fittings. The position of the fittings (INLET AND OUTLET AIR) must be agreed when ordering.

The conditioners are provided with a control panel which allows the setting of the temperature and of other parameters.

The conditioners can be provided with a COES device which guarantees the working continuity also in case of short temperature peaks up to 80°C; in addiction they can be supplied with an electrical heater for electrical panel heating, allowing to work properly up to external temperature of -40°C.

CU_ALX series are internal packaged-type, ideal for the cooling of applications electrical boards and similar items for indoor applications. They are designed to be positioned on the external wall of the cabinet.

These units work according to the cooling cycle direct expansion, so heat transfer is performed by a fluid (refrigerant) that acquires sensible heat through the evaporator coil and removes it through the condenser coil, which are parts of the sealed refrigerant circuit.

The fluid is driven by a electric motor-compressor unit. The evaporator coil is directly facing the cabinet internal, while the condenser coil faces the external room. The STANDARD basic version is equipped with analogic temperature regulation with range 25°C/35°C, ON-OFF switch and a protection fuse.

On request the series can be equipped with electronic temperature controller (CU_ALXC).

CU030ORZ ACU is packaged type, designed and manufactured to cool electrical enclosures and similar items. Very compact and light, it is designed to be positioned horizontally on the external walls of the enclosure; such a shape makes it suitable for being installed also on doors and hinged panels.

The ACU is purposely designed to allow several types of installation:

EXTERNAL MOUNTING: the ACU is mounted externally on the wall of the electrical enclosure. The advantage of this configuration is that you have no room lost in the enclosure’s internal.

INTERNAL MOUNTING: the ACU is mounted internally on the wall of the enclosure. The advantage of this configuration is that the room required externally is reduced to the dimensions of the plastic grille.

EMBEDDED MOUNTING: this mounting configuration is ideal in those situations where the solution is between the two above. For this mounting configuration a kit with frames, screws, washers and plugs is available upon order.

Electrical connection with IEC cable connector and IEC panel-mounted plug, with switch and fuse protection.

CU030ORZ features forced-air-circulation evaporator and condenser, with radial fans, to improve performances and to provide an even temperature’s distribution in the enclosure’s internal.

CAM E_ES

The system of air EXTRACTION with “Settling Chamber” has to assure continuous air exchanges, its main aim is to transfer externally the heat dissipated by the equipment in the radio base stations and Data Processing Centre.

This happens thanks to the combined operation of the air extraction and the settling chamber (inlet air).

The settling chamber can be installed externally or internally, in according with the typology of the installed air conditioners and with the space available inside the local.

SYSTEM KIT WITH SETTLING CHAMBER

• Assembly ventilation system (fan, plate grid);
• EXTERNAL/INTERNAL Settling Chamber + air filters + internal grid
• Electrical panel “Command and Control” consists of general disconnecting switch breaker, PLC, maximum temperature thermostat
• External plenum
• Overpressure damper

The system is designed to be managed by its own PLC PB13 to manage the operation cycle and detect the possible causes of alarm conditioning system.

Adjusting the temperature “ON-OFF” or “proportional” (0-10V). By adopting the regulation “proportional”, they avoid thermal shock conditions when the outside temperature is very low.

This system can also be identified as an emergency system to cool the room as it is provided an electromechanical controller (thermostat) that allows to feed the fan in an independently and separately when the detected temperature exceeds the predetermined values and simultaneously indicates the condition of emergency operation.

Type of split system air conditioner, air to air cooling, specifically designed and manufactured to operate in an industrial environment, in the presence of dust and vibration generally exposed to high temperatures.

The indoor unit “vertical” has the characteristic to be very small and it can be wall mounted. The C-Series air conditioners are designed to be controlled by a controller on board.

The C-Series is supplied with a Remote User Interface Panel for the management of command and control of the equipment. As these air conditioners are specially designed to works in industrial environments, they can operate with external temperatures up to 75° C.

Packaged air-to-air air conditioning units, designed and manufactured to work in industrial environments, in presence of dust and vibrations and exposed to high temperature.

ACU-Q Series conditioners have been designed to cool electrical enclosures and containers: every component has been designed, selected and placed to satisfy all the needs of these environments, to simplify the access to the internal parts and to minimize the maintenance.

The units must be installed on the floor, on horizontal surfaces; the air is taken from and sent to the environment to be cooled through bellows with anti-vibration stop to canalize the air.

The conditioners are provided with a remote control panel which allows the setting of the temperature and of other parameters.

The conditioners can be provided with a COES device which guarantees the working continuity also in case of short temperature peaks up to 80°C; in addiction they can be supplied with an electrical heater for warming the cabin, allowing to work properly up to external temperature of -40°C.

AE IR_CP

Indoor packaged air conditioning units air cooled type, ideals for installations inside room, shelter for radio base station and data processing centre.

Temperature can be adjusted by variation of air conditioner capacity using inverter technology (variation of compressor rotation speed).

The air conditioning units AE IR_CP series are convetional type. The cooling air is taken from the central zone and sent down.

The air conditioners P Series are equipped with internal controller and temperature and pressure probes, that allow to get an independent or coordinated “cooling system”, assuring a complete redundance of all the control and conditioning functions.

The P Series is supplied with interface user panel on board

The line of indoor air conditioning inverter units includes cooling powers of 2/8 Kw and 3/10 Kw both single-phase and three-phase.

AE ER_CP (without free cooling)

Outdoor packaged air conditioning units air cooled type, ideals for installations inside room, shelter for radio base station and data processing centre.

The adjustment of the temperature is got by means of the cooling capacity variation of the air conditioner through On Off or Inverter technology (rotation speed variation of compresor).

The air conditioning units AE ER_CP Inverter Series are convetional type. The cooling air is taken from the central zone and sent down.

The air conditioners P Series are equipped with internal controller and temperature and pressure probes, that allow to get an independent or coordinated “cooling system”, assuring a complete redundance of all the control and conditioning functions.

The P Series is supplied with remote interface user panel for the manage of commands and controls.

The line of inverter outdoor air conditioning units includes cooling powers of 2/8 Kw and 3/10 Kw both single-phase and three-phase.

RF Series packaged air conditioning units air cooled type, suitable for installations in room, shelter for radio base station and data processing centre.

RF air conditioning units can be supplied in two different versions:

• INDOOR installation
• OUTDOOR installation

The air conditioner is type CONVENTIONAL: the cooling air is taken from the UPPER side and sent from to DOWN side of theair conditioner.

This unit is equipped with free-cooling which in composed of an air exchange system, from outside to inside, through one or two fans installed on the unit and an overpressure damper to be installed in the room/shelter/radio base station(supplied), getting significant energy savings when weather conditions allow it.

The air conditioners are equipped with internal controller and temperature and pressure probes allowing the implementation of an autonomous conditioning systems and assuring a complete redundance of all the control and conditioning functions. The electronics is provided with real time clock.

The unit is equipped with remote PLC display for visualization of parameters, states and alarms.

In addition the unit can be equipped with serial RS232/485, Ethernet of GSM/GPRS card in order to allow communication with external equipment.

RF Series packaged air conditioning units air cooled type, suitable for installations in room, shelter for radio base station and data processing centre.

RF air conditioning units can be supplied in two different versions:

• INDOOR installation
• OUTDOOR installation

The air conditioner is type CONVENTIONAL: the cooling air is taken from the UPPER side and sent from to DOWN side of theair conditioner.

This unit is equipped with free-cooling which in composed of an air exchange system, from outside to inside, through one or two fans installed on the unit and an overpressure damper to be installed in the room/shelter/radio base station(supplied), getting significant energy savings when weather conditions allow it.

The air conditioners are equipped with internal controller and temperature and pressure probes allowing the implementation of an autonomous conditioning systems and assuring a complete redundance of all the control and conditioning functions. The electronics is provided with real time clock.

The unit is equipped with remote PLC display for visualization of parameters, states and alarms.

In addition the unit can be equipped with serial RS232/485, Ethernet of GSM/GPRS card in order to allow communication with external equipment.

RR Series packaged air conditioning units air cooled type, suitable for installations in room, shelter for radio base station and data processing centre.

RR air conditioning units can be supplied in two different versions:

· INDOOR installation
· OUTDOOR installation

The air conditioner without the Free-cooling module is CONVENTIONAL type: the cooling air is taken from the UPPER side and sent fromto DOWN side of the air conditioner.
The air conditioners are equipped with internal controller and temperature and pressure probes allowing the implementation of an autonomous conditioning systems and assuring a complete redundance of all the control and conditioning functions.

The electronics is provided with real time clock. The unit is equipped with remote PLC display for visualization of parameters, states and alarms.

In addition the unit can be equipped with serial RS232/485, Ethernet of GSM/GPRS card in order to allow communication with external equipment.

AE EF_CP (with free cooling)

Outdoor packaged air conditioning units air cooled type, ideals for installations inside room, shelter for radio base station and data processing centre.

The adjustment of the temperature can be achieved of the cooling capacity variation of the air conditioner through Inverter technology(rotation speed variation of compresor).

The air conditioning units AE EF_CP series are convetional type. The cooling air is taken from the central zone and sent down.
This equipment is   provided   with free-cooling. The   free-cooling system consists of air change plant, from outside to inside and vice versa, getting a significant energy savings when weather conditions permit.

The air conditioners are equipped with internal controller and temperature and pressure probes, that allow to get an independent or coordinated “cooling system”, assuring a complete redundance of all the control and conditioning functions.

The monobloc are provided with remote interface user panel for the manage of commands and controls, complete with disconnectors, with internal electrical protection for overcurrent.

The line of outdoor air conditioning units includes cooling powers of 5_8_10_14 Kw both single-phase and three-phase.

AE_IR_SP

Indoor packaged air conditioning units air cooled type, ideals for installations inside room, shelter for radio base station and data processing centre.

The adjustment of the temperature is got by means of the cooling capacity variation of the air conditioner through Inverter technology (rotation speed variation of compresor).

The air conditioning units AE_IR_SP series are underfloor type. The cooling air is taken from the central zone and sent downfloor.

The air conditioners are equipped with internal controller and temperature and pressure probes, that allow to get an independent or coordinated “cooling system”, assuring a complete redundance of all the control and conditioning functions.

The monobloc are provided with interface user panel on board for the manage of commands and controls, complete with disconnectors, with internal electrical protection for overcurrent.

CU_ROOF series ACUs are packaged-type, designed and manufactured purposely to cool electrical enclosures and similar items.
Built to be installed on roof-top of electrical enclosures, their shape makes them suitable for many other applications; the units are also equipped with very ef f icient condensate draining systems.

They work according to the principle of the reversed Rankine cycle, so heat transfer is performed by a fluid (refrigerant) that acquires sensible heat through the evaporator coil and removes it through the condenser coil, which are parts of the sealed refrigerant circuit.
The fluid is driven by a electric motor-compressor unit.
The evaporator coil is directly facing the enclosure internal, while the condenser coil faces the external room.

The CU_ROOF Series ACUs are small sized and take no room sideways the enclosure.

The Free-cooler system has the characteristic of guaranteeing continuous air changes with the primary objective of transferring the heat generated by the equipment to the external environment (for dissipation).

Solution designed to allow high ENERGY SAVING also in site where air conditioning units without free cooling system were previously installed.

AIR EXTRACTION SYSTEM

• Group ventilation system (fan, plate, grid)
• Electrical panel “Command and Control” consists of general disconnecting switch breaker, PLC and maximum temperature thermostat
• Air inlet grid with insect protection
• Dusty filter/s
• ŸPlenum external
• Overpressure damper
• Differential air pressure switch

The system is controlled by the PLC of the air conditioner which has the task of managing the operating cycle and detecting any alarm conditions. This system when coupled with an Ethra Tech air conditionercan be managed by the same air conditioner controller, without need for a dedicated PLC.

Fan speed is adjusted with “PROPORTIONAL” (0-10V) signal. By adopting the regulation “PROPORTIONAL”, are avoided thermal shock conditions when the outside temperature is very low. This system can also be identified as an emergency system to cool the room as it is provided an electromechanical controller (thermostat) that allows to feed the fan in an independently and separately when the detected temperature exceeds the predetermined values.

The Free-cooler system has the characteristic of guaranteeing continuous air changes with the primary objective of transferring the heat generated by the equipment to the external environment (for dissipation).

The VFC series air extraction system is composed by one or more centrifugal fans extracting the exhaust air from the internal environment and by a PLC controlling the entire working cycle and managing and generating the related alarm conditions.

This system when coupled with an Ethra Tech air conditioner can be managed by the same air conditioner controller, without need for a dedicated PLC.

SYSTEM COMPOSITION

• ŸVentilation group system (box + fan/s)
• Electrical panel “Command and Control” consists of general disconnecting switch breaker, PLC and maximum temperature thermostat
• Air inlet grid/s with insect protection (horizontal)
• Dusty filter/s
• External plenum+ Overpressure damper
• Differential air pressure switch

Fan speed is adjusted with “PROPORTIONAL” (0-10V) signal.

By adopting the regulation “PROPORTIONAL”, are avoided thermal shock conditions when the outside temperature is very low.

This system can also be identified as an emergency system to cool the room as it is provided an electromechanical controller (thermostat) that allows to feed the fan in an independently and separately when the detected temperature exceeds the predetermined values.

In case there is not possibility to wall mount the ventilation group system or if it necessary to install in a different position the Fans (for example in Rooms) the VFC solution can be complemented with the optional supply of one air extracting channel and related connecton duct plate.
For particular conditions, on request it can be provided the VFCS series which allows installation in critical low noise sites, by means off additional external soundproofed plenum.

AE F_PASCI

The Free-cooler system has the characteristic of guaranteeing continuous air changes with the primary objective of transferring the heat generated by the equipment to the external environment (for dissipation).

Solution designed to allow high ENERGY SAVING also in site where air conditioning units without free cooling system were previously installed.

AIR INTRODUCTION SYSTEM

• Internal free-cooler box complete dust filters and fan (centrifugal/tangential) and differential air pressure switch
• Electrical panel “Command and Control” consists of general disconnecting switch breaker, PLC PB13, maximum temperature thermostat
• External air inlet grid with insect protection
• Overpressure damper
• Internal grid
• External plenum

The system is designed to be managed by its own PLC to manage the operation cycle and detect the possible causes of alarm.

This system when coupled with an Ethra Tech air conditioner can be managed by the same air conditioner controller, without need for a dedicated PLC.

Fan speed is adjusted with “PROPORTIONAL” (0-10V) signal.

This system can also be identified as an emergency system to cool the room as it is provided an electromechanical controller (thermostat) that allows to feed the fan in an independently and separately when the detected temperature exceeds the predetermined values.

AE F _PASCE

The Free-cooler system has the characteristic of guaranteeing continuous air changes with the primary objective of transferring the heat generated by the equipment to the external environment (for dissipation).

Solution designed to allow high energy saving also in site where air conditioning units without free cooling system were previously installed.

AIR INTRODUCTION SYSTEM

• External free-cooler box complete dust filter, fan (centrifugal/tangential) and differential air pressure switch
• Electrical panel “Command and Control” consists of general disconnecting switch breaker, PLC PB13, maximum temperature thermostat
• Internal air inlet grid
• Overpressure damper
• External plenum
• Internal grid

The system is controlled by the PLC of the air conditioner which has the task of managing the operating cycle and detecting any alarm conditions.

This system when coupled with an Ethra Tech air conditioner can be managed by the same air conditioner controller, without need for a dedicated PLC. Fan speed is adjusted with  “PROPORTIONAL” (0-10V) signal.
By adopting the regulation “PROPORTIONAL”, are avoided thermal shock conditions when the outside temperature is very low.

This system can also be identified as an emergency system to cool the room as it is provided an electromechanical controller (thermostat) that allows to feed the fan in an independently and separately when the detected temperature exceeds the predetermined values.

The system of air INTRODUCTION with “Settling Chamber” has the characteristic of guaranteeing continuous air changes with the primary objective of transferring the heat generated by the equipment to the external environment (for dissipation).

This happens thanks to the combined operation of a fan positioned inside the Settling Chamber and the filtering sections.

The Settling Chamber can be installed externally or internally, in according with the typology of the installed air conditioners and with the space available inside the local.

SYSTEM KIT WITH SETTLING CHAMBER

• INTERNAL Settling Chamber + fan + air filters + external door /  EXTERNAL Settling Chamber + fan + air filters + air introduction grid
• Electrical panel “Command and Control” consists of general disconnecting switch breaker, PLC, maximum temperature thermostat
• External air extraction plenum
• Overpressure damper
• Internal plenum grid (optional)

The system is designed to be managed by its own PLC to manage the operation cycle and detect the possible causes of alarm. This system when coupled with an Ethra Tech air conditioner can be managed by the same air conditioner controller, without need for a dedicated PLC.

Fan speed is adjusted with “PROPORTIONAL” (0-10V) signal. By adopting the regulation “PROPORTIONAL”, are avoided thermal shock conditions when the outside temperature is very low. This system can also be identified as an emergency system to cool the room as it is provided an electromechanical controller (thermostat) that allows to feed the fan in an independently and separately when the detected temperature exceeds the predetermined values.

Packaged air-to-air air conditioning units, designed and manufactured to work in industrial environments, in presence of dust and vibrations and exposed to high temperature.

CUS Series conditioners have been designed to cool electrical enclosures and containers: every component has been, selected and placed to satisfy all the needs of these environments, to simplify the access to the internal parts and to minimize the maintenance.

The units must be installed on the floor, on horizontal surfaces; the air is taken from and sent to the environment to cool through ducts and insulated flexible tubes.

The conditioners are provided with two thermostats, both placed on the electrical panel, which allow the setting of the temperature of the environment to be cooled.

The conditioners can be provided with a COES device which guarantees the working continuity also in case of short temperature peaks up to 80°C; in addiction they can be supplied with an electrical heater for warming the cabin, allowing to work properly up to external temperature of -40°C.

Packaged air-to-air air conditioning units, designed and manufactured to work in industrial environments, in presence of dust, vibrations and high temperature.

ACU-P Series conditioners have been designed to cool crane control cabins: every component has been designed, selected and placed to satisfy all the needs of control cabins, to simplify the access to the internal parts and to minimize the maintenance.

The units must be wall-mountaing externaly; the air is taken from and sent to the cabin to be cooled through the openings present on the conditioner’s internal side.

The conditioners are provided with a control panel which allows the setting of the temperature and of other parameters.

The conditioners can be provided with a COES device which guarantees the working continuity also in case of short temperature peaks up to 80°C; in addiction they can be supplied with an electrical heater for warming the cabin, allowing to work properly up to external temperature of -40°C.

Packaged air-to-air air conditioning units, designed and manufactured to work in industrial environments, in presence of dust and vibrations and exposed to high temperature.

ACU-F Series conditioners have been designed to cool crane control cabins: every component has been designed, selected and placed to satisfy all the needs of control cabins, to simplify the access to the internal parts and to minimize the maintenance.

The units must be installed wall-mounting externally; the air is taken from the cabin to be cooled through an opening present on the conditioner’s internal side and sent back through an insulated flexible tube. The conditioners are provided with a control panel which allows the setting of the temperature and of other parameters.

The conditioners can be provided with a COES device which guarantees the working continuity also in case of short temperature peaks up to 80°C; in addiction they can be supplied with an electrical heater for warming the cabin, allowing to work properly up to external temperature of -40°C.

AE SF_DPV

Split air conditioning units air cooled type, ideals for installations inside room, shelter for radio base station and data processing centre.

The adjustment of the temperature can be achive by means of the cooling capacity variation of the air conditioner through Inverter technology(rotation speed variation of compresor).

The «vertical» air conditioner has the characteristic to have small dimensions, it can installed on the wall and equipped with free-cooling system (SF mod.). The part of the free-cooling can be installed on the machine (standard) or as a separate block (on request)

The  air  conditioners P Series are  equipped  with  internal  controller   and temperature and pressure probes, that allow to get an independent or coordinated “cooling system”, assuring a complete redundance of all the control and conditioning functions.

The P Series is supplied with remote interface user panel for the manage of commands and controls.

AE SR_DPV

Split air conditioning units air cooled type, ideals for installations inside room, shelter for radio base station and data processing centre.

The adjustment of the temperature can be achive by means of the cooling capacity variation of the air conditioner through Inverter technology(rotation speed variation of compresor).

The «vertical» air conditioner has the characteristic to have small dimensions, it can installed on the wall and equipped with free-cooling system (SF mod.). The part of the free-cooling can be installed on the machine (standard) or as a separate block (on request)

The air conditioners are equipped with internal controller and temperature and pressure probes, that allow to get an independent or coordinated “cooling system”, assuring a complete redundance of all the control and conditioning functions.

The air conditioners are provided with remote interface user panel for the manage of commands and controls, complete with disconnectors, with internal electrical protection for overcurrent.

The conditioners Under Series are air cooled split system, ideal for installations inside room, shelter for radio base station and data processing centre.

The adjustment of the temperature is got by means of the cooling capacity variation of the air conditioner through Inverter technology (rotation speed variation of compresor).

The airflow of the internal unit it is directed downwards.

The air conditioners are equipped with internal controller and temperature and pressure probes, that allow to get an independent or coordinated “cooling system”, assuring a complete redundance of all the control and conditioning functions.

The air conditioners are provided with remote interface user panel for the manage of commands and controls, complete with disconnectors, with internal electrical protection for overcurrent. Due to their mechanical characteristics, all the indoor units can be installed adjacent even with different cooling capacities.

This equipment is provided with free-cooling (FCUP). In case of need for ducting the free-cooling module, on request it can be provided a ducting diam. 250mm (L max 5mt) and an external grid equipped with plenum on the air inlet side. The FCUP module is a separated element from the indoor unit and its mechanical characteristics make it particularly flexible in terms of positioning and installation.

The conditioners Under Series are air cooled split system, ideal for installations inside room, shelter for radio base station and data processing centre.

The adjustment of the temperature is got by means of the cooling capacity variation of the air conditioner through Inverter technology (rotation speed variation of compresor).

The airflow of the internal unit it is directed downwards.

The air conditioners are equipped with internal controller and temperature and pressure probes, that allow to get an independent or coordinated “cooling system”, assuring a complete redundance of all the control and conditioning functions.

The air conditioners are provided with remote interface user panel for the manage of commands and controls, complete with disconnectors, with internal electrical protection for overcurrent.

Due to their mechanical characteristics, all the indoor units can be installed adjacent even with different cooling capacities.

AE SF_DP

Split air conditioning units air cooled type, ideals for installations inside room, shelter for radio base station and data processing centre.

The adjustment of the temperature can be achived by means of the cooling capacity variation of the air conditioner through Inverter technology (rotation speed variation of compresor).

The air conditioners are provided with a free-cooling system that allows a considerable energy saving when it’s permitted by the climatic conditions.

The air flow of the internal unit can be delivered vertically (displacement) or horizontally (conventional).

This equipment is provided with free-cooling. The freecooling system consists of air change plant, from outside to inside and vice versa, getting a significant energy savings when weather conditions permit.

The air conditioners are equipped with internal controller and temperature and pressure probes, that allow to get an independent or coordinated “cooling system”, assuring a complete redundance of all the control and conditioning functions.

The air conditioners are provided with remote interface user panel for the manage of commands and controls, complete with disconnectors, with internal electrical protection for overcurrent.

AE SR_DP

Split air conditioning units air cooled type, ideals for installations inside room, shelter for radio base station and data processing centre.

The adjustment of the temperature can be achived by means of the cooling capacity variation of the air conditioner through Inverter technology (rotation speed variation of compresor).

The air flow of the internal unit can be delivered vertically (desplacement) or horizontally (conventional).

The air conditioners P Series are equipped with internal controller and temperature and pressure probes, that allow to get an independent or coordinated “cooling system”, assuring a complete redundance of all the control and conditioning functions.

The P Series is supplied with remote interface user panel for the manage of commands and controls.

AE IF_SP

Indoor packaged air conditioning units air cooled type, ideals for installations inside room, shelter for radio base station and data processing centre.

The adjustment of the temperature is got by means of the cooling capacity variation of the air conditioner through Inverter technology (rotation speed variation of compresor).

The air conditioning units AE IF_SP series are underfloor type. The cooling air is taken from the central zone and sent downfloor.

The air conditioners are provided with a free-cooling system that allows a considerable energy saving when it’s permitted by the climatic conditions.

The air conditioners P Series are equipped with internal controller and temperature and pressure probes, that allow to get an independent or coordinated “cooling system”, assuring a complete redundance of all the control and conditioning functions.

The P Series is supplied with interface user panel on board

The line of indoor air conditioning units includes cooling powers of 5_8_10kW.

AE IR_DP

Indoor packaged air conditioning units air cooled type, ideals for installations inside room, shelter for radio base station and data processing centre.

The adjustment of the temperature is got by means of the cooling capacity variation of the air conditioner through compresor.

Inverter   technology (rotation   speed   variation) of the air conditioning units AE IR_DP Inverter Series are displacement type. The cooling air flow is top-down.

The air conditioners P Series are equipped with internal controller and temperature and pressure probes, that allow to get an independent or coordinated “cooling system”, assuring a complete redundance of all the control and conditioning functions.

The P Series is supplied with interface user panel on board

The line of inverter indoor air conditioning units includes cooling powers of 2/8 Kw and 3/10 Kw both single-phase and three-phase.

 AE IF_DP

Indoor packaged air conditioning units air cooled type, ideals for installations inside room, shelter for radio base station and data processing centre.

The adjustment of the temperature can be achived by means of the cooling capacity variation of the air conditioner through Inverter technology (rotation speed variation of compresor).

The air conditioning units AE IF_DP Inverter Series are displacement type. The cooling air flow is top-down.

The air conditioners are provided with a free-cooling system that allows a considerable energy saving when it’s permitted by the climatic conditions.

The air conditioners P Series are equipped with internal controller and temperature and pressure probes, that allow to get an independent or coordinated “cooling system”, assuring a complete redundance of all the control and conditioning functions.

The P Series is supplied with interface user panel on board.

The line of inverter indoor air conditioning units includes cooling powers of 2/8 Kw and 3/10 Kw both single-phase and three-phase.

AE EF_DP

Outdoor packaged air conditioning units air cooled type, ideals for installations inside room, shelter for radio base station and data processing centre.

The adjustment of the temperaturecan be achived by means of the cooling capacity variation of the air conditioner through Inverter technology (rotation speed variation of compresor).

The air conditioning units AE EF_DP series are displacement type. The cooling air flow is top-down.

This equipment is provided with free-cooling. The free-cooling system consists of air change plant, from outside to inside and vice versa, getting a significant energy savings when weather conditions permit.

The air conditioners are equipped with internal controller and temperature and pressure probes, that allow to get an independent or coordinated “cooling system”, assuring a complete redundance of all the control and conditioning functions.

The monobloc are provided with remote interface user panel for the manage of commands and controls, complete with disconnectors, with internal electrical protection for overcurrent.

The line of inverter outdoor air conditioning units includes cooling powers of 2/8 Kw and 3/10 Kw both single-phase and three-phase.

AE ER_DP

Outdoor packaged air conditioning units air cooled type, ideals for installations inside room, shelter for radio base station and data processing centre.

The adjustment of the temperature can be achived by means of the cooling capacity variation of the air conditioner through Inverter technology(rotation speed variation of compresor).

The air conditioning units AE ER_DP series are displacement type. The cooling air flow is top-down.

The air conditioners P Series are equipped with internal controller and temperature and pressure probes, that allow to get an independent or coordinated “cooling system”, assuring a complete redundance of all the control and conditioning functions.

The P Series is supplied with remote interface user panel for the manage of commands and controls.

The line of inverter outdoor air conditioning units includes cooling powers of 2/8 Kw and 3/10 Kw both single-phase and three-phase.